taper angle

This method is recommended for taper turning of external and internal surfaces when the taper angle is relatively large.

当锥角相对较大时切削外锥面和内锥面推荐使用这种方法。

When measuring, based on the segmented contour line of thread, the measurement program to calculate and measure the geometrical parameters of internal taper thread is compiled. Precisions of pitch, thread angle and taper angle reach ± 0.03mm 、± 0.24 ° and ± 0.02 °.

使用自编程序测量计算了内螺纹的螺距、牙型角和锥角，测量精度分别达到了003mm，024°和002°。

Roughing end mill with morse taper shank types and dimensions increment angle

莫氏锥柄粗加工立铣刀型式与尺寸（圆锥齿轮）齿端角

The equations for thread taper, thread pitch, thread angle and height of thread can be derived on the base of fitted lines, which are accurate enough to meet the needs of industrial measurement.

该方法可测量螺纹的锥度、螺距、螺纹夹角和螺纹高度，测量精度可以满足工业测量要求。

This feature allows both for taper bending and easy adjustment of angle differences.

这一特征允许锥度弯曲和轻松调整角差.

At present, the ring rolling technology roll one ring in one process, and the technology can't deal with stress focus on the sharp taper angle of mandrel roller.

目前锥形套圈辗扩技术只能一次成形一件，而且由于锥形套圈锥角使得芯辊应力集中严重。

Smaller taper angle of collet, larger clamping power.

弹性套锥形角更小, 故夹紧力更大.

The Optimum Taper Angle of Intaglio Mould When Two-piece Cans Thinned and Drawn

两片罐变薄拉延凹模最佳锥角

Analysis and experiment on the taper angle of contact surface of bend rotation ultrasonic micromotors

弯曲旋转超声电机接触界面锥形角的分析与实验

Process and method to solve the problem of retarded material in the extruder during production by way of improving taper angle of screw head, connector flange and structure of perforated plate are presented.

介绍了通过改进螺杆头锥角、连接件法兰以及多孔板结构以解决挤出机生产过程中滞料问题的办法。

The final tip diameter of the fiber probe obtained from experiment was between 40~ 80nm, which was satisfied with the requirements of nondestructive measurement. And the angle of taper was at around 30 °, which might ensure the efficiency of light transmission.

实验得到的光纤探针尖端直径在40～80nm之间，符合细胞内无损测量要求，探针锥形角度大约在30°，很好地保证了光的传输效率。

It is the first time to cut specially shaped tops and bottoms by the new technique of simultaneously controlling four axes of X, Y, U, V on WEDM-LS. This technique can be used to cut any kind of complicated workpiece with taper angle.

用X、Y、U、V四轴联动控制的方法，实现低速走丝线切割机床的上下异型面切割，是国内首创的通用锥度切割新工艺。

This paper describes a new method and device for measuring helical line, pitch diameter, taper and half-angle of thread of petroleum thread gauges.

本文介绍一种测量石油螺纹量规的螺旋线、中径、锥度和牙形半角的新方法及装置。

This paper presents a method for machining of taper cutting tools with equal helix angle. The principle of the method is using taper helical curve with equal pitch to approach equal angle one.

文章提出了一种在经济型数控机床上实现等螺旋角圆锥螺旋线的加工方法，其原理是用等导程螺旋线去逼近此种曲线。